Ghost Controls Electric Gate Repair Nationwide

Ghost Controls Electric Gate Repair in Orlando: What to Know First

Ghost Controls electric gate repair in Orlando typically runs $185 – $420 for common failures like dead control boards, faulty limit switches, and blown motor capacitors, and we can usually diagnose the issue on the first visit. As an independent Ghost Controls service provider, Calder Gate Repair Orlando handles the full range of Ghost Controls openers, from the single-gate R Series up through the dual-gate DTP and TSS1 heavy-duty models. We stock common Ghost Controls parts locally and quote every repair in writing before a single bolt turns. If you’re stuck with a gate that won’t open, won’t close, or beeps but doesn’t move, call (850) 338-6230 and a live person will pick up.

Call (850) 338-6230

How Ghost Controls Products Fail – and How We Fix Them

• R Series (RPB, RSH, RSP) control board failures after lightning storms. Orlando’s afternoon thunderstorms are brutal on gate electronics, and we see more fried Ghost Controls boards between June and September than the rest of the year combined. The R Series board is particularly vulnerable because it lacks the same surge protection found on some commercial brands. The symptom is usually a gate that’s completely dead with no beep, no LED, nothing. We replace the board with either an OEM Ghost Controls unit or a compatible aftermarket board, and we always recommend adding a surge protector to the outlet feeding the opener. That’s a $45 – $75 add-on that prevents a repeat visit.
• DTP Series dual-gate synchronization drift. If one gate leaf starts lagging behind the other or stops midway, the issue is usually a worn limit switch or a control board that’s lost its sync calibration. The DTP series uses an independent limit switch on each arm, and when one switch gets corroded from humidity, the board reads mismatched positions and throws the timing off. We clean or replace the affected switch, recalibrate both arms, and test the full open-close cycle five times before we call it done.
• TSS1 heavy-duty opener motor strain from improperly adjusted closing force. The TSS1 is built for big, heavy gates, but if the closing force dial gets cranked too high to compensate for a sagging hinge or a debris-filled track, the motor burns out faster than it should. In Orlando’s sandy soil, gate posts settle over time, and that slight angle change forces the opener to work harder. We check the gate geometry first, adjust the hinges and post alignment if needed, then set the force dial to the manufacturer’s recommended range. Replacing a TSS1 motor without fixing the underlying alignment is just buying another motor in eighteen months.
• Ghost Controls keypad and remote signal loss after battery corrosion. Florida humidity eats batteries, and corroded terminals inside the wireless keypad or remote are a common cause of “the gate only works from the wall button.” The keypad sends a signal to the receiver, but if the board inside the keypad has rusted contacts, the signal never leaves. We open the unit, clean the contacts with contact cleaner, replace the battery with a lithium version that holds up better in humidity, and re-pair the keypad to the board. If the corrosion has damaged the circuit trace, we replace the keypad outright.
• Safety sensor false trips from Orlando’s intense sun angle. Ghost Controls photo eye sensors can false-trigger when direct morning or late afternoon sun hits the receiver lens at a low angle. The gate will start to close, then immediately reverse, over and over. It’s not a board problem – it’s the sensor being blinded. We re-aim the eyes slightly, install a small sun shield, or reposition the receiver to a shadier spot on the post. In some cases we swap the photo eyes for a newer generation sensor with better sunlight filtering.

Our Ghost Controls Electric Gate Repair Process

1. 1
   You call (850) 338-6230. A live person answers, asks what the gate is doing (or not doing), and schedules a time that works. You get a live, trackable arrival time on the day of service, not a four-hour window.
2. 2
   We show up and diagnose. Nico or one of the crew tests the opener, checks the board for error codes, and traces the problem. If it’s a board issue, we test voltage at the terminals. If it’s mechanical, we check the arm, hinges, and limit switches. No guessing – we confirm the failure before quoting anything.
3. 3
   You get a written price. We put the repair cost on paper (or text it to you) before any work starts. That price includes parts, labor, and any adjustments we need to make. The number you approve is the number on the invoice.
4. 4
   We make the repair. We use OEM Ghost Controls parts when they’re available and the best option, or quality aftermarket components from brands we trust when OEM is backordered or overpriced for what it is. We’ll tell you which one we recommend and why, in plain English.
5. 5
   We test and document. The gate gets cycled repeatedly, the safety sensors are checked, and the closing force is verified. You get before-and-after photos and a digital invoice you can pay from your phone.
6. 6
   You’re covered for 365 days. Every repair carries the 365-Day Done Right Promise in writing. If the repair fails within a year, we come back and fix it at no charge. That’s the deal, every time.

What Ghost Controls Electric Gate Repair Costs in Orlando

Most Ghost Controls electric gate repairs in Orlando fall between $185 and $420 before parts, depending on what’s actually wrong. A limit switch replacement is usually at the low end. A control board replacement on an R Series opener lands in the middle. A full TSS1 motor swap on a heavy dual gate is the upper range and sometimes beyond, especially if we’re also correcting gate alignment. Parts are quoted separately and always in writing. We don’t charge extra for weekends or evenings, and every quote includes the diagnostic time – you won’t see a surprise “assessment fee” tacked on. Call (850) 338-6230 and we’ll give you a straight answer on what your specific repair should cost.

Why Orlando Homeowners Call Calder Gate Repair Orlando for Ghost Controls Work

We’re part of the Relay Home Co. family, operating under The Relay Visibility Guarantee since 2009. For you, that means a live arrival time you can track, a technician in uniform who shows up when they said they would, and a written price before anything starts. Our techs are trained on nine major opener brands, so if your Ghost Controls system needs replacement and you’re weighing options, we can talk honestly about LiftMaster, Mighty Mule, DoorKing, and others without steering you toward whatever’s easiest for us. The 365-Day Done Right Promise covers every Ghost Controls repair we make. If it’s not right, we return and make it right – free. That’s the whole point.

FAQs