Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Orlando?
A new driveway gate installation in Orlando typically runs between $2,800 and $9,500 for a complete single gate system in 2026, with most homeowners landing between $4,000 and $6,500 for a mid-range automatic gate. A basic chain-link or tubular steel manual gate starts closer to $1,200, while a custom wrought iron double gate with full automation and intercom can push past $15,000. Those ranges include the gate itself, posts, hinges, and installation labor – but the opener, electrical work, and any masonry on brick or stucco columns gets priced separately.
Calder Gate Repair installs gates throughout Orlando neighborhoods like College Park, Baldwin Park, Dr. Phillips, Winter Park, and Lake Nona. Every project starts with a written price before any work begins – the number we quote is the number on your invoice, full stop.
Gate Installation Cost Breakdown (2026)
| Component | Typical Orlando Price Range |
|---|---|
| Manual single gate (chain-link or tubular steel) | $1,200 – $2,800 |
| Single automatic gate (aluminum or steel) | $2,800 – $5,500 |
| Double automatic driveway gate | $4,500 – $9,500 |
| Wrought iron or custom ornamental gate | $6,000 – $14,000+ |
| Gate opener unit only (LiftMaster, FAAC, BFT, etc.) | $600 – $1,800 |
| Electrical run and panel hookup | $400 – $1,200 |
| Concrete footing and post setting | $300 – $900 per post |
| Installation labor (typical 1-day single gate job) | $800 – $2,200 |
| Permit and inspection fees (Orange County, if required) | $150 – $500 |
Those numbers reflect what we’re seeing across Orange County and Seminole County in 2026. The biggest swing factor is almost always the gate material and whether the opener needs a new electrical line run from the panel. In older Orlando homes – think 1950s and 60s-era neighborhoods around Colonialtown or Audubon Park – existing conduit is often undersized for modern openers, so the electrical work adds more than it would in a newer Lake Nona build.
Salt air and moisture also matter more than homeowners expect. Even in inland Orlando, summer humidity plus frequent afternoon storms means we strongly recommend aluminum or powder-coated steel over raw steel. The upfront cost is maybe 10-15% higher, but raw steel in Central Florida will rust at the welds within three to five years unless you are religious about maintenance.
For a deeper walkthrough of what a full project involves from measuring to final programming, see our guide on Gate Installation in Orlando.
What Affects Gate Installation Pricing in Orlando
Here are the six levers that move a gate quote most in this market:
- Gate material. Aluminum is the sweet spot for Orlando: it handles humidity without rust and runs $2,800 to $6,000 for a typical single gate. Steel costs less upfront but needs more maintenance. Wrought iron looks great on older Winter Park estates but starts around $6,000 and goes up fast with custom scrollwork.
- Single vs. double gate. A double gate means two leafs, two post sets, often two openers or a single opener with a connecting bar. That adds $1,500 to $4,000 over a comparable single gate.
- Opener brand and horsepower. A basic Mighty Mule or Ghost Controls unit runs $600 to $900. A heavy-duty LiftMaster or BFT operator built for a 1,000-lb gate runs $1,200 to $1,800. Calder is factory-familiar with all of them – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so we match the opener to the gate weight and cycle frequency, not the other way around.
- Column and masonry work. If your driveway has existing brick or stucco columns, retrofitting a gate mount is straightforward. If you need new columns poured and faced, expect $1,200 to $3,500 added to the job. We will not pour footings in Orlando during the wet summer months without checking the ground first; sandy soil in some parts of Orange County needs a deeper footing than standard specs call for.
- Power and site readiness. Running a new dedicated circuit from the panel to the gate is $400 to $1,200 depending on distance and whether we have to go under a driveway. If a trench has to cross concrete, the price jumps.
- Accessories. Keypads, remote controls, vehicle exit sensors (the loops or photo eyes that tell the gate to open when a car pulls up), and smartphone controllers all add $150 to $500 per item. An intercom wired to your house adds $700 to $1,800.
Orlando-Specific Notes on Gate Pricing
Two facts shape gate pricing here more than any national average ever will: humidity and homeowners associations.
First, humidity. Orlando’s average relative humidity sits above 70% most of the year, and June through September brings near-daily thunderstorms. That means circuit boards inside opener housings fail faster here than they do in drier climates. It is the single most common call we run in July and August – an opener that worked fine in April suddenly stops responding after a storm. When we install, we use weather-sealed housings and dielectric grease on every board connection, and we put surge suppression on the line if the panel is older.
Second, HOAs. A lot of Orlando’s newer communities – Baldwin Park is the classic example, but also large sections of Hunter’s Creek, Avalon Park, and parts of MetroWest – have written gate standards. They can dictate gate color, material, height, and even whether the gate must swing inward or slide. If you live in a community with a gate design standard, we recommend getting the HOA spec sheet before the site visit. It takes one email, and it prevents a $5,000 gate from being declined by your association’s architectural review committee.
DIY vs. Professional Gate Installation
You can buy a Mighty Mule or Ghost Controls kit online for $500 to $800 and install it over a weekend if you have an existing gate. For a smart, handy homeowner that is a legitimate option. But there is a line: the gate itself, the posts, and the electrical work are not a weekend project.
Setting a gate post wrong is a $1,500 mistake. If the post is out of plumb, the gate sags, the opener burns out faster, and you will be back doing the job again within two years. Pouring a footing for an automatic gate in Orlando soil means digging below the frost line is not a concern here the way it is up north, but sandy loam does not hold a post the way clay does, so we use larger diameter concrete cylinders than a generic internet tutorial shows.
And the electrical side deserves real respect. Gate openers run on 110V or 220V circuits. Running a new circuit through conduit, under a driveway, or into an existing panel is work that should be done by someone who does it every week, not every few years. That is if your local code requires a dedicated circuit and an accessible disconnect switch within sight of the opener – which Orange County does. If you already own a gate and the opener has stopped working rather than a fresh install, our home page covers what we repair and how fast we can get to you.
Gate Install Process: What the $4,500 Actually Buys
A mid-range Orlando gate installation job looks something like this:
Step 1: Site visit and written quote
We come out, measure the driveway opening, check the panel distance, look at what is under the soil surface, and hand you a written price before we leave. That price includes the gate, posts, opener, labor, and any permit fees we can identify at that stage. If we find something during the job that was hidden – a buried cable, an unexpected concrete pad – we stop and show you before any added cost gets approved.
Step 2: Permits and HOA check
Not every gate in Orlando requires a permit. A manual gate on an existing driveway with no electrical work usually does not. The moment an automatic opener is added and a circuit is run, Orange County generally wants a permit and an inspection. We handle that paperwork as part of the job, which is part of why our labor line item is at the higher end of the range you will see elsewhere.
Step 3: Footing and post setting
We dig, frame, and pour the footings. Concrete cures for a minimum of 48 hours before we hang anything on it. If you request it, we can schedule in two visits so the gate is never suspended on temporary supports.
Step 4: Gate hang and level
We mount the hinges, hang the gate, and spend the time to get it plumb and level in both directions. This is where good installs separate from bad ones. A gate that is a quarter-inch out of level will swing shut on its own or bind at the latch.
Step 5: Opener install and programming
We mount the opener, run the wiring, and program the limits by hand – setting the open and close points precisely, not just using the factory defaults. We then walk the remote controls, keypad codes, and any phone app through with you before we consider the job done.
Step 6: Final walkthrough and invoice
You see the gate open and close in front of us, you get before-and-after pictures, and the invoice you pay matches the number on the written quote. The job carries the 365-Day Done Right Promise in writing: if anything about the installation fails within 365 days, Calder returns and makes it right at no charge. That includes a free second visit – not a pro-rated service call.
Common Gate Installation Add-Ons and What They Cost
The base gate is only part of the number. These are the add-ons Orlando homeowners ask for most:
- Keypad entry – $180 to $350 installed. A weather-sealed keypad on a gooseneck post.
- Two or three handheld remotes – $40 to $90 each, depending on brand.
- Smartphone control module (LiftMaster MyQ, BFT, or Ghost Controls app bridge) – $250 to $600 installed and connected to your WiFi.
- Vehicle exit sensor loop – $500 to $900. This is the in-ground sensor that opens the gate automatically when a car pulls up from the inside. It requires cutting and sealing a section of driveway.
- Keyed manual release – $120 to $250. A lockable override so you can open the gate by hand if the power is out and the battery backup is dead.
- Battery backup – $300 to $700. Given that summer storms knock out power in pockets of Orlando every single year, this is one we recommend to nearly every customer with an automatic gate.
- Intercom or video doorbell at the gate – $700 to $1,800 for a hardwired system, less for a WiFi-based video unit.
How to Save on Gate Installation in Orlando
Half of saving money on a gate is buying the right gate once. Here is what we tell every homeowner who asks how to keep the number down:
- Choose aluminum over ornamental steel. Aluminum in Orlando costs more day one, but it does not rust in the humidity and it does not need repainting every three years. Over a 10-year span, aluminum is cheaper.
- Buy the opener and the gate from the same company that installs them. That sounds obvious, but a lot of people buy a kit online and then call us for an install. When the opener arrives already married to a gate we did not size it for, the install takes longer and costs more in labor.
- Standardize on one keypad and one set of remotes per household. Adding a second keypad later is a second service call. Adding it during the install is just parts.
- Do not skip the battery backup. A $500 battery is cheaper than a $1,200 repair when a storm surge damages the board. This is one add-on that repays itself in Orlando’s storm climate.
- Get a written quote that includes everything. We give you a written price before work starts – that has been our standard since the day Relay Home Co. started in 2009, and it is mandatory at Calder Gate Repair, never optional. If another company will not put the number in writing before the job, get another company.
Want an exact number for your driveway? Call (850) 338-6230 and a live person answers 24/7. You will get a real price in writing, not a ballpark.
FAQs – Gate Installation Cost
How much does a gate opener cost in Orlando?
A gate opener unit alone runs $600 to $1,800 in Orlando depending on the brand and the weight of the gate. Entry-level Mighty Mule and Ghost Controls openers start around $600; a commercial-grade LiftMaster or FAAC opener for a heavy double gate runs $1,200 to $1,800. Installation and programming add $300 to $800 to that number. Call (850) 338-6230 and we will quote your opener installed in writing, free.
Is it cheaper to repair a gate or replace it?
Most gate opener repairs in Orlando land between $180 and $450. If the gate itself is structurally sound – no rot at the welds, no sag, no rust-through – repairing is almost always cheaper than replacing. But if the gate has been sagging for years and the opener has burned through two circuit boards, a new gate install at $2,800 to $6,500 is the smarter money. We will tell you which one you are looking at before any work starts, and the price is in writing either way.
How long does gate installation take in Orlando?
A standard single automatic gate install takes one full day once the concrete has cured. Footings need 48 hours to set, so the job is usually spread across two visits: day one for footing and post setting, day two for the gate, opener, and programming. Custom double gates with masonry work can take three to five days on site. We schedule the date and give you a live, trackable arrival time – not a four-hour window.
Do I need a permit for a gate in Orlando?
An automatic gate with a new electrical circuit generally requires a permit in Orange County. A manual gate on existing posts with zero electrical work usually does not. Calder handles the paperwork as part of the install, so you do not have to sort out county requirements. If you are in a city with its own building department – Winter Park, Maitland, or Belle Isle – the specific rules vary slightly, and we check with the right office before we file.
What gate brand do you recommend for Orlando’s climate?
For most Orlando homeowners, we recommend LiftMaster or Ghost Controls for the opener and aluminum for the gate itself. Both opener brands have weather-sealed boards that hold up better in high humidity than most budget options. For gates, aluminum is the only material we do not have to warn customers about rusting within a few years. We carry and service all nine major brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so the recommendation is never forced.
Get a Written Gate Installation Quote in Orlando
You should know the exact number before you sign anything. You should know what time the installer lands, what brand of opener is going on your driveway, and what the invoice will say. That is how Calder Gate Repair runs every job from the first phone call to the final walkthrough. We are part of the Relay Home Co. family, and we have held that standard since 2009.
A live person answers every call at (850) 338-6230, 24 hours a day. Call now for a free estimate on your Orlando gate installation, and you will have a written price before the first tool comes off the truck.
Pricing reflects the Orlando market as of 2026. Calder Gate Repair Orlando offers free estimates – call (850) 338-6230.
Written by Nico Alvarez, Owner at Calder Gate Repair Orlando, serving Orlando since 2009.
What Our Customers Say
"Keypad and remotes reprogrammed in one visit. Paid by link."
- Pauline C."Slide gate wheels replaced. Glides smoothly now."
- Mark T."Booking was easy and the job was done quickly."
- Seth R.